The LabLynx is a portable battery powered digital Acquisition system. It is capable of recording from up to 256 individual electrodes through the use of Neuralynx Digital Multiplexing Headstages, MUX. The physiological signals are digitized at the Neuralynx MUX Headstage and transmitted wirelessly from the LabLynx via 5G WiFi to a wireless access point connected to a PC running Cheetah software.
This document describes the specifications and features of the LabLynx. It also explains how to set up, test, and use your LabLynx. There is a glossary at the end of the document.
Please see attached PDF.
Version 1.0, 2019-01-15
Table of Contents
1 Document Overview .......................................................................... 5
2 LabLynx Overview ............................................................................. 5
2.1 LabLynx Components ..................................................................................... 6
2.1.1 LabLynx Base ............................................................................................... 6
2.1.2 Battery Charger Cable................................................................................... 6
2.1.3 Wireless access point kit ............................................................................... 6
2.1.4 16 or 32 channel MUX Headstage ................................................................ 6
2.2 Electrostatic Sensitive Equipment ................................................................... 7
2.3 Recommended Additional Products ................................................................ 7
2.3.1 Neuralynx Digital Multiplexing (MUX) Headstages ....................................... 7
2.3.2 Signal Mouse ................................................................................................ 7
2.3.3 Minirator Kit .................................................................................................. 7
2.3.4 HS-36-MUX Impedance Plug ...................................................................... 8
2.3.5 2Pin to BNC Cable......................................................................................... 8
2.3.6 Neuralynx Halo Microdrives ......................................................................... 8
3 Quick Start ........................................................................................ 9
3.1 Connecting a LabLynx to a PC ......................................................................... 9
3.2 Set Ethernet port IP address .......................................................................... 10
3.2.1 Clear LabLynx for firewall ............................................................................. 10
3.2.2 Configure Cheetah for specific LabLynx setup ........................................... 10
3.3 Software quick start ....................................................................................... 12
3.3.1 Start Cheetah and turn on LabLynx ............................................................. 12
3.3.2 Connect LabLynx to test setup ................................................................... 12
Drive Signal into LabLynx ..................................................................................... 13
4 Hardware Overview ........................................................................... 17
4.1 Enclosure overview ......................................................................................... 17
4.1.1 UDB-25 input connector .............................................................................. 18
4.1.2 10 Pin connector ......................................................................................... 21
4.1.3 24 Pin connector ......................................................................................... 21
4.1.4 Transmit Status Indicator ............................................................................ 22
4.1.5 ON/Off Push button .................................................................................... 22
4.1.6 Manufacturing Access Panel....................................................................... 22
4.1.7 Battery Charger ........................................................................................... 22
4.1.8 Battery Charge indicator ............................................................................. 22
4.1.9 Back Panel Mounting locations .................................................................. 23
4.2 LabLynx Amplifier and A/D Converter ............................................................. 23
4.3 LabLynx Communication .................................................................................. 23
4.4 Optimizing data stream and masking CSC ........................................................ 24
4.4.1 Channel masking overview ......................................................................... 24
4.4.2 Channel mapping overview ........................................................................ 24
5 Optimizing Wifi channel..................................................................... 25
1 Software Overview ............................................................................ 26
2 Configuring TTL inputs ...................................................................... 26
LabLynx Commands ............................................................................. 27
2.1 WHSSetDigitalIOPortDirection ......................................................................... 27
2.2 WHSSetDigitalIOBit .......................................................................................... 28
2.2 WHSSetDigitalIOBit .......................................................................................... 28
2.3 WHSSetDigitalIOPortValue .............................................................................. 28
2.4 WHSSetTransmittedChannels ............................................................................ 29
Neuralynx Contact .................................................................................. 30
Comments
0 comments
Please sign in to leave a comment.